Shifter Boot Clips / Plastic Boot Frame (3D Printed)

J'ai conçu des clips améliorés pour le support de démarrage d'eBay Shifter. Il m'a cassé en une semaine après avoir collé mon nouveau sélecteur F10. J'avais donc 2 options, enlever le démarrage du levier de vitesses du plastique et en acheter un nouveau, ou concevoir de nouveaux clips qui résisteront pour toujours.

Ce eBay on a des clips très fragiles, donc je les ai tous remplacés avec mon clip de conception et voila... Il s'est cassé dans l'endroit comme un champion. Ces clips sont imprimés avec PETG, donc très flexible et ne se cassera pas dans les hautes températures ou même si vous le pliez à 180 degrés.

Je suis hors du marché et n'imprime pas de nouveaux cadres ou clips, mais j'ai décidé de rendre le projet ouvert et gratuit pour tout le monde.

Voici le lien: https://www.printables.com/model/345239-bmw-e92-m3-manual-shifter-frame-and-clips

Les dons seraient appréciés. Merci à tous!

Nice work!

6ixSpd wrote

Nice work!

Thanks man! Hopefully, this will help someone in need.

Amazing. Does this work with DCT shifter? I assume yes? If so I’ll take a set.

MaximusB wrote

Amazing. Does this work with DCT shifter? I assume yes? If so I’ll take a set.

I don't think so :/ I designed it to fit manual trans boot holder. Have no idea how dct trans lever clips into the place.

Can I buy just 1 to try? Will let you know if it’ll work on a dct.

Yeah, PM me.

Shipping is $4 though.

Very interested in this. Do you break off the original tabs and then superweld glue these onto the same spots?

ling.media wrote

Very interested in this. Do you break off the original tabs and then superweld glue these onto the same spots?

Yeah, one was already broken off, so I broke off other 3 and filed the spot down, then used super weld to glue it on the same spot.

buglinjo wrote

Yeah, one was already broken off, so I broke off other 3 and filed the spot down, then used super weld to glue it on the same spot.

Gotcha. Can you elaborate on filing the spot down? Did you use some sandpaper to rough up the area behind the old tab, sandpaper for better adhesion, etc?

ling.media wrote

Gotcha. Can you elaborate on filing the spot down? Did you use some sandpaper to rough up the area behind the old tab, sandpaper for better adhesion, etc?

No, I used a file to shave that bulge down. You can see in the picture. When you break the tab off, that bulge will stay there, so you need to flatten it first.

I’ll take a set, DM me your PayPal info please.

donut_boi wrote

I’ll take a set, DM me your PayPal info please.

DMed

buglinjo wrote

No, I used a file to shave that bulge down. You can see in the picture. When you break the tab off, that bulge will stay there, so you need to flatten it first.

Ah I see. I'll take a set - message me your Paypal

ling.media wrote

Ah I see. I'll take a set - message me your Paypal

DMed

I'll buy, i don't even know if I need it, but i'm buying LOL?

Richneerd wrote

I'll buy, i don't even know if I need it, but i'm buying LOL?

Haha lol, DM me.

I guess I need to print more, sold already 100 of clips lol

count me in. dm sent

Pm'd you. Need a set.

Process of printing

So I bought some of these clips from buglinjo. They were ABSOLUTELY PERFECT! Not only were they shipped quickly, but the fit was perfect. Well, made and the design is MUCH better than the OEM clips.

I had installed the new M5 knob and the leather is much thicker. Nicer than the original M3's, I really liked the new leather but the original clips would not take. I trimmed to the point that there was barely enough on the plastic frame but the original clips still would not engage.

After the clips arrived, I used a small hacksaw blade (for metal) to slowly cut off the original clips and then the inside edge (bump) that was part of the clip - made it all smooth. I used J&B epoxy and some of the metal binder clips to hold the new clips in place while the epoxy cured.

After wrestling with the shift boot with the original clips I was ready for a fight trying to get the revised boot to snap in. Attached the wire and pressed the plastic ring into place. It attached immediately and perfectly. The fit is great. Done-finally.

A long post for some plastic clips but they made all the difference. If you're thinking of the knob/ boot mod for the M3, use these clips. I would have saved myself significant trouble if I had installed these clips from the start. Nice work buglinjo!

Johnr3524 wrote

So I bought some of these clips from buglinjo. They were ABSOLUTELY PERFECT! Not only were they shipped quickly, but the fit was perfect. Well, made and the design is MUCH better than the OEM clips.

I had installed the new M5 knob and the leather is much thicker. Nicer than the original M#'s, I really liked it but the original clips would not take. I trimmed to the point that there was barely enough on the plastic frame but the original clips would not engage.

I used a small hacksaw blade (for metal) to slowly cut off the original clips and then the inside edge (bump) that was part of the clip - made it all smooth. I used J&B epoxy and some of the metal binder clips to hold the new clips in place while the epoxy cured.

After wrestling with the shift boot with the original clips I was ready for a fight trying to get the revised boot to snap in. Attached the wire and pressed the plastic ring into place. It attached immediately and perfectly. Done-finally.

A long post for some plastic clips but they made all the difference. If you're thinking of the knob/ boot mod for the M3, use these clips. I would have saved myself significant trouble if I had installed these clips from the start. Nice work buglinjo!

Thank you for your post!

I'm glad I helped other people like me struggling to keep boot holder in place.